HamsterBearF1C200sv5.17LinuxRTL8188EUS适配

HamsterBear F1C200s v5.17 Linux RTL8188EUS 适配

• 平台 - F1C200s

• Linux版本 - 5.17.2

• Buildroot - v2022.2

底板做了USB HUB， 用的是FE1.1s，一共做了4路，其中一路拿来连wifi模块，另外
3个直接做成了USB Type-A接口

进入 kernel menuconfig 打开如下选项

（该驱动位于staging下，选择编译进内核）

buildroot中选择如下软件包

（主要是net-tools iw工具包）

启动系统后

1. 修改musb 为host模式

echo host > /sys/devices/platform/soc/1c13000.usb/musb-hdrc.1.auto/mode[ 1379.560411] phy phy-1c13400.phy.0: Changing dr_mode to 1[ 1380.223933] usb 1-1: new high-speed USB device number 2 using musb-hdrc[ 1380.405841] hub 1-1:1.0: USB hub found[ 1380.409764] hub 1-1:1.0: 4 ports detected[ 1380.833942] usb 1-1.1: new high-speed USB device number 3 using musb-hdrc[ 1381.146412] r8188eu: module is from the staging directory, the quality is unknown, you have been warned.[ 1381.170314] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)[ 1381.205020] EEPROM ID = 0x8129[ 1381.212399] usbcore: registered new interface driver r8188eu

ip addr 可以看到对应wifi接口

# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1000    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00    inet 127.0.0.1/8 scope host lo       valid_lft forever preferred_lft forever2: usb0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 1000    link/ether 52:8c:6f:55:1f:64 brd ff:ff:ff:ff:ff:ff3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 1000    link/ether 54:ef:33:d6:5e:72 brd ff:ff:ff:ff:ff:ff

2. 连接到wifi

上电

# ifconfig wlan0 up[ 1687.899356] R8188EU: Firmware Version 11, SubVersion 1, Signature 0x88e1[ 1688.274263] MAC Address = 54:ef:33:d6:5e:72

扫描附近wifi

# iwlist wlan0 scanwlan0     Scan completed :          Cell 01 - Address: 8C:DE:F9:EC:55:8B                    ESSID:""                    Protocol:IEEE 802.11bgn                    Mode:Master                    Frequency:2.422 GHz (Channel 3)                    Encryption key:off                    Bit Rates:144 Mb/s                    Quality:0  Signal level:0  Noise level:0          Cell 02 - Address: 96:DE:F9:EC:55:8B                    ESSID:"kernelbot"                    Protocol:IEEE 802.11bgn                    Mode:Master                    Frequency:2.422 GHz (Channel 3)                    Encryption key:off                    Bit Rates:144 Mb/s                    IE: Unknown: DD820050F204104A0001101044000101103B00010310470010876543219ABCDEF012340AA3C33C838F102100067869616F6D69102300045241383110240004303030321042000531323334351054000800060050F2040001101100135849414F4D495F524F555445525F4755455354100800020000103C0001031049000600372A000120                    Quality:0  Signal level:0  Noise level:0

连接到wifi

# iwconfig wlan0 essid kernelbot# iwconfiglo        no wireless extensions.usb0      no wireless extensions.wlan0     IEEE 802.11bgn  ESSID:"kernelbot"  Nickname:"<WIFI@REALTEK>"          Mode:Managed  Frequency:2.422 GHz  Access Point: 96:DE:F9:EC:55:8B          Bit Rate:72.2 Mb/s   Sensitivity:0/0          Retry:off   RTS thr:off   Fragment thr:off          Encryption key:off          Power Management:off          Link Quality=100/100  Signal level=0 dBm  Noise level=0 dBm          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

请求ip

# udhcpc -i wlan0udhcpc: started, v1.35.0udhcpc: broadcasting discoverudhcpc: broadcasting select for 192.168.19.234, server 192.168.19.1udhcpc: lease of 192.168.19.234 obtained from 192.168.19.1, lease time 43200deleting routersadding dns 192.168.19.1

尝试访问外网(没接天线)

# ping baidu.comPING baidu.com (220.181.38.148): 56 data bytes64 bytes from 220.181.38.148: seq=0 ttl=50 time=201.784 ms64 bytes from 220.181.38.148: seq=1 ttl=50 time=225.148 ms64 bytes from 220.181.38.148: seq=2 ttl=50 time=15.126 ms64 bytes from 220.181.38.148: seq=3 ttl=50 time=116.496 ms64 bytes from 220.181.38.148: seq=4 ttl=50 time=115.356 ms64 bytes from 220.181.38.148: seq=5 ttl=50 time=21.000 ms64 bytes from 220.181.38.148: seq=6 ttl=50 time=114.353 ms64 bytes from 220.181.38.148: seq=7 ttl=50 time=122.406 ms^C--- baidu.com ping statistics ---8 packets transmitted, 8 packets received, 0% packet lossround-trip min/avg/max = 15.126/116.458/225.148 ms

更多玩法

1. MQTT与上位机通信

	大概业务就是 扫描传感器数据上报给上位机	上位机也可以指定从机行为

2. 移植浏览器访问网页

3. 挂载主机NFS文件系统

4. 做内网WEB服务器

5. 暂时没想到

总结以及遇到的一些问题

总结

因为一开始设计思路就比较清晰，所以整个过程还是比较顺利的，底板设计的时候，因为
粗心大意连错了线，所以又再版了。

内核 buildroot那两块等有空再写详细点。

有问题可以联系我邮箱(writeforever@foxmail.com)

问题

1. 模块上电后扫描自动断开连接
   后来发现是供电不够，一开始一直用电脑USB接口供电，但那个最大电流貌似就500mA，
   换了个充电头就ok了。